-
Call Us +8613677218585 -
Mail Us info@isuzutruckscn.com -
Isuzu NKR 4x4 manlifter truck
The Isuzu NKR 4x4 offroad Manlifter Trucks designed to fully rely on the advantages of the original chassis, fully consider the product's convenience and reliability. Working arms in the form of three folding with working height can be 16m, the vehicle advantages of a large work area, can adapt to different working conditions’ requirements. Powertrain system using hydraulic transmission fitted on slewing rotation saddle and bucket each with a separate operating system, the operation system priorities then bucket operations
Work capacity:
16 mTruck model:
PT5070JGK16ZEngine power:
120 HPEngine type:
4KH1CNAxle drive:
4×2Gear box:
MSB 5-speed, manualRemarks:
Japan ISUZU NKR 4x4 truck chassis mounted 16m folding arm manlifter kitThe Isuzu NKR 4x4 offroad 4WD aerial platform truck also called Isuzu 4x4 Bucket Truck, Isuzu NKR 4x4 manlifter truck, which equipped with overflow protection, emergency power, cylinder lock and other security devices to ensure safety operations. Cab for the single-row seat, comfortable driving. Therefore, the vehicle is an ideal multi-purpose aerial vehicle. The detailed English Version Operation Manual is to enable the operator to understand of controlling of the Isuzu 4WD Man Lifter Truck with Crane allows the operator to use the equipment effectively and safely. Before operation, you must be fully read with this manual. Any lifting equipment operated by untrained or careless user, are potentially dangerous. The Isuzu NKR 4x4 Manlifter Truck hydraulic system designed advanced, with a safe and reliable technology. However, any equipment without maintenance could not keep the equipment in good working condition, the operation will potentially dangerous. So you are familiar with the equipment itself before the operating process goes. Any unclear changes or operations for this Isuzu NKR 4x4 Aerial Platform truck, you must immediately report to the superiors or notify the manufacturer.
Product Parameters for Isuzu NKR 4x4 offroad aerial platformt ruck:
1. PTO 2. Oil Pump 3. ISUZU single cabin Chassis
4. Hand brake 5. Rotary Center Joint 6. Slewing Support
7. Hydraulic Leg Control box 8. Hydraulic Legs 9. Slewing Reducer
10. Hydraulic Motor 11. Bucket 12. Arms Control Box
13. 3rd Arm (Bucket) 14. Swing Mechanism 15. 3rd Arm Hydraulic Cylinder
16. 2nd Arm Hydraulic Cylinder 17. 1st Arm (Upper Arm)
18. 2nd Arm (Lower Arm) 19. Lifting Cylinder
20. 1st Arm Hydraulic Cylinder 21. Lifting Arm 22. Lifting Hook
| Chassis Specification for Isuzu NKR 4x4 manlifter truck |
|||
| Truck model | PST5070JGK16Z | ||
| Cab | ISUZU 600P single row of seats cab, with air-conditional and USB connector radio. | ||
| Driving Type | 4*4 Left hand driving | ||
| Max Speed (km/h) | 90 | ||
| Overall dimension (mm) | Appro. 8400*1980*3100 | ||
| GVW (kg) | Appro. 6800 | ||
| Mass in working order ( kg) | Appro. 6485 | ||
| Wheelbase (mm) | 3815 | ||
| Tire | 7.00R16 | ||
| Clutch | Single-plate dry diaphragm spring clutch | ||
| Steering | Hydraulic steering with power assistance | ||
| Gear box | MSB 5-speed | ||
| Bridge | Front axle | 2.5T | |
| Rear axle | 4.8T | ||
| Engine | Model | 4KH1CN | |
| Fuel Type | Diesel fuel | ||
| Emission Standard | Europe 5/6 | ||
| Type | Water-cooled four-stroke, supercharged inter-cooling | ||
| Exhaust (ml) | 2999 | ||
| Max output power/rotate speed (hp /rpm ) | 120/3400 | ||
| Max torque/rotate speed (N.m/rpm) | 220/1700 | ||
| Braking System | Service Brake | Oil brake | |
| Park Brake | Spring energy | ||
| Electric system | 12v | ||
| Special Function | |||
| Working height (m) | 16 | ||
| Max working radius (m) |
8.8
|
||
| Boom type |
Three sections folding working boom
|
||
| Rated loading in the bucket(kg) |
200
|
||
| Bucket size (mm) |
1300*1000*1000
|
||
| Rotating speed (r/min) |
0-2
|
||
| Rotation angle |
360°
|
||
| Supporting leg |
four sets hydraulic legs
|
||
|
Horizontal
|
3500mm
|
|
|
longitudinal
|
4000mm
|
||
| Boom control mode |
1.Bucket control
2.Manual operation
|
||
| Supporting legs |
Four hydraulic supporting legs with manual operation
|
||
|
Features:
1. Front H and rear H legs, good stability, which can be operated at the same time or independently, and adapt to a variety of working conditions.
2. Computer controlled, automatic limit, alarming when in dangerous work, excellent safety performance.
3. With a monitor, real-time display of the vehicle operating conditions.
4. Hexagonal working arm, synchronization telescope, compact structure, high efficiency and wide operating range.
5. External telescopic cylinder, chain telescopic mechanism, easier to observe the fault point, convenient maintenance.
6. The vehicle has two operation ways : platform operation and operating on the ground which is safe, reliable and high efficiency.
7. Slewing mechanism adopts adjustable type, which is easy to adjust.
8. Non-slip body
9. Toolbox (2 pieces)
|
|||
What should known for Isuzu NKR 4x4 manlifter trucks manufacturer from POWERSTAR:
Ø Before use, you must check whether the Isuzu 4x4 Man Lifter Truck with normal maintenance or not. (See seven)
Ø Before the operation, must be assured that the manlifter truck in a solid level ground. To determine the hand brake on brake position, all the necessary accessories must be in place (such as tire pads, safety warning flags, etc.). Legs must be supported on solid ground, in order to ensure stability. If you must work on slopes situation (max 5 °), must be fully extended legs, and operated in high-slope side
Ø Getting on/off the Isuzu bucket truck, should use the provided the bucket ladder, running and pad.
Ø The operator on the bucket must wear protective safety equipment specification requirements, and fixed in a safe anchor ring.
Ø The protective equipment has been used by the operator must be consistent with the work requirements, must meet safety standards.
Ø In operating equipment such as rotary or lifting arm, etc., must be confirmed no traffic obstruction, no obstructions or around high-voltage interference.
Ø Make sure that the Isuzu truck mounted boom lift maintains in a certain distance and pedestrians out away from the work area.
Ø Under the Arms/Booms is prohibited with mankind standing.
Ø Control valve should be operated and handled slowly, in order to achieve smooth movement, to prevent a sudden start or stop, to prevent contact with solid objects, arm and bucket work, such as tree branches, buildings, etc.
Ø Could not allowed the bucket in a situation of side working ,next to the bucket load, or lift from the bucket to the un-target subject, bucket prohibit to hang goods.
Ø Rated bucket loading 200kg, not allowed to overload. Rated load, including operators, tools, articles all of those.
Ø Not Allowed to stand, sitting on the edge of the bucket and human body lean on the bucket edge are prohibited either.
Ø The bucket of the Isuzu 4x4 aerial platform truck not allowed putting with ladder, cushions inside, and any approach of increase height of working are prohibited.
Ø Not allowed move the truck in the situation that bucket inside with human beings, otherwise it will lead to personal injury.
Ø Truck in moving or running, the arms and legs must be in the normal contraction.
Ø As operation or malfunction is found, please report immediately to the manufacturer.
Isuzu Chassis 14m Truck Mounted Aerial Working Platform Isuzu Brand 14M Telescopic Boom Aerial Working Platform Technical Parameters (PT5061JGK10S GKS-14QX) Working Condition 1, Altitude: 0-1000m 2, Temperature: -25° C--+45° C, environmental relative humidity ≤ 90% 3, Allowed working condition: Solid, stable land, the vehicle should be horizontal 4, Wind force: ≤ 6 degree (wind speed ≤ 12.5m/s ) Working Range PT5061JGK Telescopic Boom Aerial Working Platform can be applied in various conditions for aerial working, such as urban road, suburban road, highway, airport, bridges and culverts and so on. The structure type is telescopic boom and the lifting boom is flexible, convenience and performance with the negative point, more suitable for narrow site conditions or other special operations. Bulletin No. KFM5061JGK10S Type GKS-14QX External dimensions ( mm ) 7050×2020×3250 Structure type Three-section telescopic boom Working Cage Internal size ( mm ) 1200×600×1100 Rated loading ( kg ) 200 ( or 2 persons ) Max. Working height ( mm ) 14000 Max. Height from ground ( mm ) 12300 Max. Working radius ( mm ) 9300 Working radius when doing the highest height ( mm ) 1320 Working Boom Lifting angle of main boom ( º ) -24_78° Out rate speed ( mm/sec ) 8500/50 Ret rate speed ( mm/sec ) 8500/50 Boom rack rotation angle ( º ) 360 Boom rack rotation speed ( r/min ) 1.0 Outrigger Vertical span ( mm ) 3050 Horizontal span ( mm ) 3600 Traveling of vertical outrigger ( mm ) 450 Adjustment Single adjustable
Learn More
Isuzu bucket truck lift,Isuzu truck mounted aerial lift,ISUZU Bucket Articulating Truck Mounted Lift
Learn More
Truck Mounted Aerial Work Platforms,Isuzu rotary platform and the working basket,Isuzu Vehicle Mounted Boom Lift three telescopic arms truck
Learn More
Isuzu Truck Mounted Aerial Work Platforms,Isuzu truck mounted boom lift,Isuzu 2 Ton Truck Mounted Aerial Lift
Learn More
Mobile Isuzu emergency communication truck for sale,Communication command vehicle emergency rescue supply truck,Mobile communication truck
Learn More
ISUZU articulating boom lift, truck mounted boom lift, truck mounted aerial lift, bucket truck lift,Aerial Platform Truck isuzu,High quality Isuzu Aerial Working Truck Mounted Lift 200kg
Learn More
Max work height 20/22m ISUZUhigh-altitude operation truck, Aerial Platform Operation Truck,aerial operation vehicle,hydraulic aerial cage,aerial working platform truck
Learn More
