ISUZU News

Product brief description The compressed garbage truck consists of a sealed garbage compartment, a hydraulic system, and an operating system. The whole vehicle is fully sealed. It is self-compressing, self-dumping, and all sewage during the compression process enters the sewage tank. This completely solves the problem of secondary pollution during garbage transportation and avoids inconvenience to people.   1.The key components are made of Imported components have the advantages of high pressure, good sealing, easy operation, and safety. 2. Product performance and characteristics (1) The curved box greatly increases the box volume and enhances the beauty of the vehicle. (2) The power take-off adopts a well-known domestic brand, Jiashan power take-off, specially equipped for special vehicles, perfectly matched with the engine and gearbox, and has a low failure rate Low. (3) The oil pump adopts a well-known domestic brand and is equipped with a compaction valve to increase the compression density and loading capacity. The loading capacity is equivalent to two and a half times that of non-compressed garbage of the same tonnage. (4) The oil tank is enlarged and the volume is increased to prevent the high temperature of the hydraulic oil. All hydraulic oil must be added to the oil tank through a hydraulic oil filter to filter impurities in the hydraulic oil, reduce the failure rate, and effectively prevent damage to accessories. Multi-way valves are used Sino-foreign joint venture brand, Weisen Bole multi-way valve, matched with Weisen Bole cylinder, low failure rate, CAN bus control method; less wiring, low failure rate, automatic display of fault codes, convenient maintenance and repair. (5) External oil cylinder: The skateboard oil cylinder is external, which has high efficiency, is not easy to get stuck in garbage, and is easy to maintain in the future. (6) Operation automation: adopts dual system control of photoelectric switch and time, with one-button unloading, with wireless remote control device, all filling Only one driver is required to operate during the discharge operation, and two operating modes, fully automatic and semi-automatic, can be set, which not only reduces the labor intensity of sanitation workers, but also greatly improves the working environment. (7) Dual insurance system: The operating system has dual functions of computer control and manual operation, which greatly protects and improves the utilization rate of the vehicle. The pressure regulating valve changes position to prevent customers from adjusting the pressure without authorization. The power take-off is equipped with a warning to remind customers to turn on and off the power take-off to prevent damage to the power take-off. (8) Turning mechanism: A turning mechanism with a garbage can (or bucket) can be optionally installed. 3. Product advantages (1) Since the compressed garbage truck has a complex upper structure and a large self-mass, reducing the ...

With the development of urbanization, sanitation trucks are used more and more frequently, such as ISUZU sewage suction trucks, which are relied on for sewage treatment in urban communities. Heavy duty ISUZU sewage suction trucks can also be used for sewage treatment in factories and enterprises. ISUZU sewage suction trucks are special-purpose vehicles, its operation method is different from ordinary vehicles. Many users who want to buy a sewage suction truck want to learn how to operate a sewage suction truck. Today I will introduce to you how a sewage suction truck discharges sewage.   The sewage from the ISUZU sewage suction truck contains sewage and sludge. Generally, the sewage is discharged first and then the sludge. The specific method is as follows: 1. First move the four-way valve to the "neutral" position, and then move the drain valve to the "open" position, mainly relying on gravity for drainage. 2. Then move the four-way valve of the sewage suction truck to the discharge position and let the vacuum pump continue to work, so that compressed air will flow into the tank and the sewage will be discharged faster. 3. Pressure can also be used to drain sewage from sewage suction trucks. First, open the drain valve and move the four-way valve to the discharge position. This can avoid excessive pressure in the tank from affecting the sealing of the back cover or other accidents.   After the sewage is discharged, the sludge needs to be discharged. The discharge of sludge is more complicated than that of sewage: 1. First, depress the clutch, move the reversing valve to the "open" position, or push the power take-off lever to run the oil pump. 2. Then open the ball valve on the back cover to discharge part of the sewage and reduce the pressure in the tank to communicate with the atmosphere. 3. Open the locking device of the back cover, loosen the handle and completely pull out the screw. 4. Move the tank door opening and closing lever of the manual reversing valve of the sewage suction truck to the "open" position. Before opening, confirm whether the pressure in the tank is equal to atmospheric pressure. If the rear tank cover is opened under negative pressure, Will damage the sealing ring and cylinder. 5. Adjust the hydraulic lifting device of the manual reversing valve to the "rising" position. 6. After the sludge is discharged, adjust the operating range of the hydraulic cylinder to the "descended" position. After safely descending, check the parts: Check whether there is mud on the back cover flange and sealing ring. If there is any mud, use a brush to clean it, close Back cover secure the locking device of the back cover to ensure the sealing of the back cover.   The above steps may seem simple, but they are indispensable. Each step must be done in place, so that the sewage can be discharged smoothly and the vehicle can be protected to the greatest extent.

The first level of maintenance focuses on lubrication and tightening. In addition to performing routine maintenance items, the following inspections must also be performed.Clean the engine fuel filter, air filter, oil filter, and hydraulic system air filter. Add grease to the oil nozzles at each hinge point, and apply grease to the surface of the slide in the trash bin and filler. Check the tightness of the connection, check the connection between the garbage bin and the frame, the connection between the shovel slide block and the push shovel, the hinge shaft of the loader slide block, and the pin shaft of each oil cylinder, and tighten them if necessary. Secondary maintenance: performed every 250 hours of operation, Second-level maintenance focuses on inspection and adjustment, and implements all items of first-level maintenance. Check the pressure of each pressure valve in the hydraulic system. If there is any deviation, it should be adjusted in time (by professionals); clean the oil suction filter element of the hydraulic system and check the oil return filter pressure. When the oil return filter pressure pointer reaches 0.08MPa, replace it in time. Oil filter assembly (disposable); check the connection and sealing conditions of each joint and sealing surface; replace the high-pressure hose in time when cracks, partial damage, aging and expansion are found. Check whether the filter in the gas line system is blocked and whether the air pipe is cracked or aged, and replace it if necessary. Check the condition of the rubber sealing strip on the joint surface of the garbage bin and the filler and the rubber gasket of the drain valve, and replace them if necessary. Check the blade slide block and loader slide block as well as the wear of each pin and bushing, and replace them if necessary. Check whether the welds of each assembly are cracked and de-welded, whether the structure is plastically deformed, and whether the pin is cracked. Problems found should be eliminated promptly. Check the pressure filling cycle and discharge time. If they are too fast or too slow, they should be adjusted to normal conditions. Level three maintenance: performed every 1,000 hours of operation, The third level of maintenance focuses on the disassembly, cleaning, inspection, adjustment and elimination of hidden dangers of some assemblies. Perform all levels of primary and secondary maintenance. Check the hydraulic fluid condition. If it is found that the hydraulic oil has many pollutants, is turbid and black, has foam emulsification, and has large changes in viscosity, the hydraulic oil must be replaced. Note: When replacing the hydraulic oil, the pusher cylinder, lift cylinder and skateboard oil are in a fully retracted state, and the scraper cylinder is in a fully extended state. After the old oil is drained, remove the coarse and fine oil filters in the tank and clean the coarse filters. , oil drain plug and oil tank, and replace them after cleaning. Add clean hydra...

ISUZU sewage suction trucks and ISUZU cleaning sewage suction trucks are both sanitation vehicles and play their respective roles in environmental construction. ISUZU sewage suction trucks are mainly used for sewer sewage treatment in some urban communities and sewage treatment in some factories and enterprises. Sewage suction trucks are special-purpose vehicles. It is inevitable that some faults will occur after a long time of use, which will affect work efficiency. Therefore, it is best for us to master some emergency measures for sewage suction trucks, which may be able to solve urgent problems at critical moments.   1. The oil tank leaks. This situation must be dealt with in time, otherwise other dangerous accidents may easily occur. At this time, you can wipe the oil leakage clean first, and use soap or bubble gum to apply to the oil leakage area to temporarily plug the leak. If there is epoxy Resin adhesive is better. Use it directly to repair, and the effect will be better. 2. The oil pipe is broken. In this case, you can first wipe the rupture clean, apply soap or use tape to wrap around the rupture of the entire oil pipe, tie it tightly with iron wire, and then apply a layer of soap. 3. The oil pipe is broken. In this case, you can find a rubber or plastic pipe with the same diameter as the oil pipe to connect it. If the sleeve is not tight enough, the two ends can be tied tightly with iron wire to prevent oil leakage. 4. If there are blisters in the cylinder head of the sewage suction truck, resulting in oil and water leakage, you can select an electrician's fuse of corresponding specifications according to the size of the blisters, and gently smash it into the blisters with a hand hammer to eliminate oil and water leaks. 5. There is oil leakage at the oil pipe joint. When the sewage suction truck is in use, if there is oil leakage from the engine oil pipe joint, this situation is mostly caused by the poor sealing between the oil pipe bell mouth and the oil pipe nut. At this time, you can use cotton yarn to wrap under the horn. Then tighten the oil pipe nut and the oil pipe joint. You can also chew gum or maltose into a paste and apply it to the oil pipe nut seat. After it dries and solidifies, it can play a sealing role. 6. The inlet and outlet hoses of the sewage suction truck are cracked. If the crack is small, you can use a cloth strip to simply wrap the leakage. If the crack is large, it is best to put a bamboo pipe or iron pipe on the cracked area and use iron wire to tie it. tight. 7. The fan belt is broken. At this time, you can wrap the broken belt with iron wire, or drive the car away by starting and stopping. 8. Screw hole slider. Screw hole slider will cause oil leakage or loosening of the connecting rod, making it unable to work. At this time, the original screw can be flattened with a hammer to expand both sides, and then tightened. This way The method cannot be used multip...

With the ISUZU sewage suction truck, it is much easier to treat sewer sewage in urban areas and sewage from factories and enterprises. It is one of the necessary models in sanitation trucks. There are many brands of sewage suction trucks,ISUZU is the best brand. But most of their functions are similar, the operation methods are also very similar. In the process of use, one or other faults will inevitably occur. Some faults must be solved in time, otherwise they may cause more serious consequences, because as a user of a sewage suction truck, it is best to master Some sewage suction truck maintenance methods can be used for emergency relief at any time. 1. The vacuum gauge of the sewage suction truck reads too low or has no indication. a. The vacuum pump speed is too low, solution: increase the throttle; b. The vacuum gauge tube is blocked, solution: clear the blockage; c. The vacuum meter is damaged, solution: replace the vacuum meter; d. The four-way ball valve is not fully opened. Solution: replace the rotary vane. 2. Leakage from the hole cover of the sewage suction truck： a. The left-hand screw is not screwed in place. Solution: screw the left-hand screw in position; b. The sealing gasket is damaged and fails. Solution: replace the sealing gasket; c. The tie rod is too long, solution: adjust the length of the tie rod. 3. What should I do if the power take-off of the sewage suction truck makes abnormal noise and the temperature rises? a. Parts are worn, solution: dismantle and inspect, clean the power take-off and replace worn parts; b. The lubricating oil contains impurities or is insufficient. Solution: replace the lubricating oil or add lubricating oil in time. 4. What should I do if the vacuum pump of the sewage suction truck makes abnormal noise and the temperature rises too high? a. If impurities enter the pump cavity or debris is generated, the solution is to disassemble, inspect, clean the vacuum pump and replace worn parts; b. The wheel cover is worn, solution: replace the wheel cover. c. The lubricating oil is insufficient and mixed with impurities. Solution: add or replace lubricating oil in time. 5. What should I do if the fuel tank of the sewage suction truck leaks? a. The connecting screw is loose, solution: tighten the bolt; b. The sealing gasket is damaged, solution: replace the sealing gasket; c. The amount of lubricating oil is too large. Solution: The lubricating oil surface is located in the middle of the liquid, which is the appropriate position.

Routine maintenance of Isuzu garbage compression truck, After daily operation of the Isuzu garbage compression truck, rinse the body, wipe the glass and rearview mirror; rinse the inside of the garbage bin, filler and sewage tank to remove residual garbage. When washing the vehicle, do not spray water directly into electrical components and fuel tanks. On the air intake hole. Clean the sealing joint surface to ensure a good seal, and avoid damaging the rubber sealing strips and gaskets due to sharp or hard objects in the garbage. 1.Check the engine oil level and coolant level, and add if necessary. After starting the engine, listen to see if it is running normally, and check if the car's instruments, lights, service brakes, parking brakes, steering system and power take-off are normal. 2.Check the liquid level in the hydraulic oil tank. The oil level in the oil tank must not be lower than the minimum height indicated by the oil mark. If the oil is insufficient, add oil. Inspection method: The pusher cylinder and slide cylinder are in the fully retracted position, the scraper cylinder is in the fully extended position, and the loader is in the closed state. 3.Check the working device controls, electronic control buttons and sensors. If there are any problems, they should be adjusted or replaced in time. Check the entire vehicle for oil, water, and air leaks. Check whether the tire nut, various bolts, nuts and pins are loose; check the tire appearance and air pressure. Troubleshoot problems that occurred on the day. Routine maintenance of an Isuzu garbage compression truck typically includes the following tasks: Daily Inspection: Before using the truck, inspect the exterior, tires, lights, mirrors, and other essential components. Check for any visible damage or leaks. Engine Oil and Filter Change: Regularly change the engine oil and oil filter as per the recommended schedule. This ensures proper lubrication and prolongs the life of the engine. Air Filter Replacement: Replace the air filter as per the manufacturer's recommendations. A clogged air filter can affect engine performance and fuel efficiency. Fuel Filter Replacement: Replace the fuel filter to prevent contaminants from entering the fuel system. This is crucial for maintaining optimal engine performance. Fluid Levels Check: Regularly check and top up fluids such as coolant, brake fluid, power steering fluid, and hydraulic fluid as needed. Battery Maintenance: Check the battery terminals for corrosion, clean them if necessary, and ensure the battery is securely mounted. Test the battery and replace it if it is weak or not holding a charge. Tire Inspection: Check the tire pressure, tread depth, and overall condition of the tires. Rotate the tires regularly to ensure even wear. Brake Inspection: Regularly inspect the brake pads, rotors, and brake lines for wear or damage. Replace any worn components immediately to maintain optimal braking performance. Lubrication: Apply lubricant to hinges, l...

On June 25th, POWERSTAR TRUCKS was pleased to welcome esteemed customers from Saudi Arabia to visit our factory.The clients had previously contacted us for a quote for ISUZU freezer trucks and want to know our production facilities and processes in this visit. The customers expressed their intention to purchase a large number of Isuzu refrigerated trucks, and came to our factory to fully understand the specifications, performance and production process of the vehicles. Previous requests for quotes have shown that they are seriously considering POWERSTAR as their preferred supplier. During the visit, the customer had an in-depth tour of our advanced production facilities of refrigerated trucks. They had the opportunity to witness the streamlined production process, advanced equipment and strict quality control measures that make our refrigerated vehicles stand out in terms of durability and performance.Customers also showed special interest in our tank truck production line. Our team introduced them to our advanced automated welding technology, which ensures superior structural integrity and durability. The visit of our Saudi Arabian customers to the POWERSTAR factory was a fruitful and promising event. We are excited about the prospect of working with them to provide them with high quality ISUZU special vehicles to their exact specifications.

POWERSTAR TRUCKS supplied two units of ISUZU GIGA 6 wheeler water foam fire trucks to Philippines. These ISUZU fire fighting trucks are designed to efficiently handle all types of fire emergencies, making them an indispensable tool in firefighting operations. These ISUZU GIGA fire trucks are specially designed for our Philippines customer. The vehicles are based on ISUZU GIGA 6 wheeler heavy duty chassis, which comes with ISUZU 420HP diesel engine, FAST 9-speed manual gearbox. The trucks are equipped with 6000 liters water tank and 2000 liters foam tank, both of the tanks are made in high quality stainless steel. The fire trucks are also equipped with advanced lighting systems including sirens, beacons, work lights and emergency lights, ensuring great visibility during operations. Now these ISUZU GIGA fire fighting trucks have been put into service in the Philippines. Its high-performance water and foam pump, ample water and foam supplies, and advanced advanced lighting system make it efficient in suppressing fires quickly. Customer are very satisfied with these fire trucks.

Philippine fire trucks are specialized vehicles used by firefighters to respond to fires and other emergency situations in the Philippines. These Isuzu fire trucks are equipped with different types of firefighting equipment, such as hoses, water tanks, pumps, and ladders, as well as communication devices and other safety gear. There are several types of Philippine fire trucks, such as pumper trucks, which are the most common type and used to carry water and other firefighting agents to the scene of a fire; ladder trucks, which are equipped with extendable ladders used to reach high structures; and aerial tower trucks, which have an elevated platform for firefighting operations and rescue operations.   Most Philippine fire trucks are manufactured locally by Filipino companies or imported from other countries, such as Japan and the United States. These trucks are operated by the Bureau of Fire Protection (BFP), a government agency responsible for ensuring public safety by preventing and controlling fires in the Philippines. Isuzu fire fighting truck is a popular brand of fire trucks in the Philippines. Some of the most common Isuzu fire trucks used in the country include: 1. Isuzu FVR900P fire truck: This fire truck has a maximum power of 240 horsepower and can carry up to 3,000 liters of water. 2. Isuzu FTR fire truck: This fire truck has a maximum power of 240 horsepower and can carry up to 2,800 liters of water. 3. Isuzu NQR fire truck: This fire truck has a maximum power of 190 horsepower and can carry up to 2,000 liters of water. 4. Isuzu NPR fire truck: This fire truck has a maximum power of 150 horsepower and can carry up to 1,500 liters of water. These Isuzu fire trucks are equipped with various features such as high-pressure pumps, foam tanks, storage cabinets for equipment, and firefighting tools. They are also designed to operate well in different terrain and weather conditions.

On August 28th, 2022, 15 units of ISUZU Garbage Compactor Trucks were delivered from POWERSTAR factory. These rear loader garbage trucks were delivered to Shanghai port to catch the RORO on September 3th.       These 15 units ISUZU refuse compactors trucks are the second batch for Dominica government. The first batch of 26 units waste compactors were delivered by POWERSTAR TRUCKS in July 2021. These waste compactors are based on original ISUZU ELF 100P light duty and FTR medium duty truck chassis, the compactor body capacity is 6CBM for 100P chassis and 14CBM for FTR chassis. All the compactor bodies are equipped with China famous hydraulic cylinders and hydraulic pump, CAN-bus control system for easy operation.     POWERSTAR TRUCKS is a professional manufacturer and exporter of garbage compactors in China, who exports ISUZU refuse compactors more than 15 years with good reputation. We offer reliable and durable waste compactors based on ISUZU ELF 100P, 700P, FTR, FVR, FVZ and GIGA chassis. We also customize waste compactor bodies based on customers chassis, such as ISUZU, FUSO, Benz, MAN, ect.  

On August 8th, 2022, POWERSTAR produced ISUZU 700P 4×4 Passenger Carrier Truck  was delivered to Shanghai port to catch RORO. The truck will be shipped to Ethiopia. This ISUZU 700P 4×4 AWD troop carrier truck is customized for our Africa customer. Mr Brady is a business man from Ethiopia who regularly procures special purpose vehicles for their government. In July of this year, he got the order of 1 unit ISUZU 700P 4×4 troop carrier truck. He got information of POWERSTAR TRUCKS from his business partner, who purchased from us ISUZU garbage compactor truck and vacuum tank truck last year. After several emails, we know his requirements very well. We provided our design proposal based his requirements and make CAD drawing for final confirmation. One month later, the truck was completed and ready for shipment. The ISUZU 4×4 Soldier Carrier Truck  is based on ISUZU 700P 4×4 all wheel drive medium duty chassis, equipped with ISUZU 190HP Euro 5 diesel engine, MLD 6-speed manual gearbox. The van body is made of high quality carbon steel, installing 20 seats with belts, air conditioner, tempered fixed glass windows, LED light, etc.

On July 26th, 2022, one unit ISUZU 600P 4×4 Garbage Compactor Truck  was delivered to Shanghai port from POWERSTAR factory. The truck will be loaded in 40HC container at Shanghai port. This ISUZU 600P 4×4 AWD garbage truck is for our Philippines customer. Mr Simon is our regular customer who have purchased from us ISUZU dump trucks, ISUZU water tank trucks, ISUZU man lifters and crane trucks. In June of this year, he placed the order of one unit ISUZU 600P 4×4 rear loader. According to his requirements, we make him CAD drawing and start the production process soon. The ISUZU 4×4 6CBM Refuse Compactor Truck  is based on ISUZU 600P 4×4 all wheel drive light duty chassis, equipped with ISUZU 130HP Euro 5 diesel engine, MSB 5-speed manual gearbox. The compactor body is made of high quality wear resistance steel, the capacity is up to 6CBM. The waste compactor truck is equipped with China famous hydraulic cylinders and CAN-bus control system.